KISHO Glass Coating

Designation of product: kisho deluxe glass coating kit

Designation of product: kisho deluxe glass coating kit
Content: 
1. 1 Si-811 glass coating agent (30ml); 
2. 1 X-03 protectant (30ml); 
3. 1 Glass coating sponge; 
4. 1 Manual. 
kisho deluxe glass coating kit
Product features: 
Si-811 glass coating agent, is featured with advantageous performances of enhancing finish glossiness, water repellency and anti-fouling, forming a genuine protective film to car paint. Combined practice with X-03 protectant after practice, can protect the coating film in its hardening stage, and also can effectively prevent raindrop imprint, enabling perfect glass coating effectiveness.
kisho glass coating
Instructions: 
Pre-practice treatment 
Finish treatment before vehicle glass coating is dependent on finish conditions, and it is critical to the practice, for inferior treatment may influence the adhesiveness and basic performance of glass coating film, thus please determine whether it needs iron powder removal, grinding and polishing, and air gun blow-off procedures on basis of the finish conditions, but do note that degreasing is necessary. 
deluxe glass coating kit
Precautions before the practice 
1. This product is fast try, please avoid practice under burning sun, otherwise wiping would be impeded; 
2. Avoid practice in temperature environment under 10℃; 
3. Please carry out practice under complete cool-off state of the vehicle body, since vehicle body heat may expedite product hardening rate leading to wiping obstruction; 
4. Please completely clear fouling attached on vehicle body and carry out degreasing before practice;
5. Please read practice manual in details and follow practice procedures therein. 
kisho deluxe glass coating kit
Si-811 glass coating agent practice method 
1. Drip Si-811 glass coating agent to coating sponge for 7-10 drops, first swear it laterally, then swear it vertically with "#" pattern, recommended at 50cm*50cm for each practice area, and note the usage quantity, since excessive usage per time may lead to non-uniform smearing or wiping obstruction; 
2. Wait 2-8 minutes to wipe after smearing, first use a wet towel to wipe with even strength (no need to wipe repeatedly, just spread the glass coating agent), then immediately use a dry towel to wipe the glass coating layer, until the surface is bright and smooth. Wiping duration recommendation: 30℃=within 3 min, 20℃=within 5 min, 10℃=within 8 min, glass coating hardening rate is directly correlated with temperature and humidity, thus it is recommended to measure local temperature and humidity before determining the wiping duration; 
3. Check wiping omission for each part under completion, until the whole vehicle is covered. 
4. Single practice of glass coating effectiveness is well enough, nevertheless the second practice will increase thickness and durability of coating film, in this case please exercise the second practice after previous one no sooner than 1-2 hours.
kisho deluxe glass coating kit
X-03 protectant practice method 

After completion of whole vehicle Si-901 glass coating practice, postpone for above 2 hours to carry out X-03 protectant practice;
1. Jiggle before practice, spray X-03 protectant on the finish, 4 to 5 times for half the hood.; 
2. Use a dry towel to gently wipe in alternate lateral and vertical linearly, then use another dry towel to wipe with polishing brightness to complete; 
3. It is recommended a practice of X-03 protectant for every 3-6 months of the vehicle to better protect the glass coating film. 
Notice: Do not use excessive quantity leading to nonuniform practice. 
Note: 
1. Do not smear the whole vehicle by one time, to avoid difficulty of post-hardening treatment, please carry out practice part by part;
2. While wiping dry, observe the surface in well lighted location, to avoid remaining residue, and if indoor illumination is inferior, drive the vehicle outdoor to conduct inspection and wiping in full range, to ensure perfect practice quality; 
3. After practice, complete hardening of the coating film requires around 1 week, thus do not engage water or rinse the vehicle before complete hardening;